manualshive.com logo in svg

NXP Semiconductors LCP43 Series, User Manual

Share
Download
NXP Semiconductors LCP43 Series User Manual Download Page 482

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2012. All rights reserved.

User manual

Rev. 1.3 — 6 July 2012 

482 of 1269

NXP Semiconductors

UM10503

Chapter 21: LPC43xx External Memory Controller (EMC)

Note: This register is used for all four dynamic memory chip selects. Therefore the worst 
case value for all of the chip selects must be programmed.

 

21.7.17 Dynamic Memory Load Mode register to Active Command Time 

The DYNAMICTMRD register enables you to program the load mode register to active 
command time, tMRD. It is recommended that this register is modified during system 
initialization, or when there are no current or outstanding transactions. This can be 
ensured by waiting until the EMC is idle, and then entering low-power, or disabled mode. 
This value is normally found in SDRAM data sheets as tMRD, or tRSA. This register is 
accessed with one wait state.

Note: This register is used for all four dynamic memory chip selects. Therefore the worst 
case value for all of the chip selects must be programmed.

 

21.7.18 Static Memory Extended Wait register 

ExtendedWait (EW) bit in the StaticConfig register is set. It is recommended that this 
register is modified during system initialization, or when there are no current or 
outstanding transactions. However, if necessary, these control bits can be altered during 
normal operation. This register is accessed with one wait state.

 

Table 369. Dynamic Memory Active Bank A to Active Bank B Time register (DYNAMICRRD - 

address 0x4000 5054) bit description

Bit

Symbol

Description

Reset 
value

3:0

TRRD

Active bank A to active bank B latency
0x0 - 0xE = n + 1 clock cycles. The delay is in CCLK cycles.
0xF = 16 clock cycles (POR reset value).

0xF

31:4

-

Reserved, user software should not write ones to reserved bits. The 
value read from a reserved bit is not defined.

-

Table 370. Dynamic Memory Load Mode register to Active Command Time (DYNAMICMRD - 

address 0x4000 5058) bit description

Bit

Symbol

Description

Reset 
value

3:0

TMRD

Load mode register to active command time.
0x0 - 0xE = n + 1 clock cycles. The delay is in CCLK cycles.
0xF = 16 clock cycles (POR reset value).

0xF

31:4

-

Reserved, user software should not write ones to reserved bits. The 
value read from a reserved bit is not defined.

-

Table 371. Static Memory Extended Wait register (STATICEXTENDEDWAIT - address 

0x4000 5080) bit description

Bit

Symbol

Description

Reset 
value

9:0

EXTENDEDWAIT Extended wait time out.

16 clock cycles (POR reset value). The delay is in CCLK 
cycles.
0x0 = 16 clock cycles.
0x1 - 0x3FF = (n+1) x16 clock cycles.

0x0

31:10 -

Reserved, user software should not write ones to reserved bits. 
The value read from a reserved bit is not defined.

-

Summary of Contents for LCP43 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands