manualshive.com logo in svg

NXP Semiconductors LCP43 Series, User Manual

Share
Download
NXP Semiconductors LCP43 Series User Manual Download Page 1160

UM10503

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2012. All rights reserved.

User manual

Rev. 1.3 — 6 July 2012 

1160 of 1269

NXP Semiconductors

UM10503

Chapter 44: LPC43xx 10-bit ADC0/1

44.6.2 A/D Global Data register 

The A/D Global Data Register contains the result of the most recent A/D conversion when 
the ADC operates in software-controlled, non-burst mode (BURST bit set to zero and 
START bits set to 0x1 in the CR register). This includes the data, DONE, and Overrun 
flags, and the number of the A/D channel to which the data relates.

Remark: 

Use only the individual channel data registers DR0 to DR7 with burst mode or 

with hardware triggering to read the conversion results.

 

44.6.3 A/D Interrupt Enable register 

This register allows control over which A/D channels generate an interrupt when a 
conversion is complete. For example, it may be desirable to use some A/D channels to 
monitor sensors by continuously performing conversions on them. The most recent 
results are read by the application program whenever they are needed. In this case, an 
interrupt is not desirable at the end of each conversion for some A/D channels.

Table 1011.A/D Global Data register (GDR - address 0x400E 3004 (ADC0) and 0x400E 4004 

(ADC1)) bit description

Bit

Symbol

Description

Reset 
value

5:0

-

Reserved. These bits always read as zeroes. 

0

15:6

V_VREF

When DONE is 1, this field contains a binary fraction representing 
the voltage on the ADCn pin selected by the SEL field, divided by 
the reference voltage on the VDDA pin. Zero in the field indicates 
that the voltage on the ADCn input pin was less than, equal to, or 
close to that on VSSA, while 0x3FF indicates that the voltage on 
ADCn input pin was close to, equal to, or greater than that on 
VDDA.

-

23:16 -

Reserved. These bits always read as zeroes. 

0

26:24 CHN

These bits contain the channel from which the LS bits were 
converted.

-

29:27 -

Reserved. These bits always read as zeroes. 

0

30

OVERRUN

This bit is 1 in burst mode if the results of one or more conversions 
was (were) lost and overwritten before the conversion that 
produced the result in the V_VREF bits.

0

31

DONE

This bit is set to 1 when an analog-to-digital conversion completes. 
It is cleared when this register is read and when the AD0/1CR 
register is written. If the AD0/1CR is written while a conversion is 
still in progress, this bit is set and a new conversion is started.

0

Summary of Contents for LCP43 Series






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands