manualshive.com logo in svg

NXP Semiconductors KITPF5200FRDMEVM, User Manual, Page: 5 / 51

Share
Download
NXP Semiconductors KITPF5200FRDMEVM User Manual Download Page 5

NXP Semiconductors

UM11723

KITPF5200FRDMEVM evaluation board

•

Power supply with a range of 3.3 V to 5.0 V. Current limit depends of the use case, but

a 4.0 A current limit supports all use cases

3.3 Windows PC workstation

This evaluation board requires a Windows PC workstation.

•

USB-enabled computer with Windows 7 or Windows 10

3.4 Software

The following software must be installed on the PC workstation prior to using the

KITPF5200FRDMEVM evaluation board.

•

PF5200 NXP GUI installation package

4 Getting to know the hardware

4.1 Kit overview

The KITPF5200FRDMEVM kit provides an integrated platform for evaluating designs

based on NXP’s PF5200 dual-channel PMIC. All PF5200 features can be accessed and

monitored in a test environment.
The kit hardware consists of the KITPF5200FRDMEVM evaluation board, a FRDM-

KL25Z microcontroller board, and the USB cable required to connect the FRDM-KL25Z

to the PC.
The KITPF5200FRDMEVM evaluation board features an individual PF5200 soldered

on board. Connectors, jumpers, and switches on the board can be used to configure an

evaluation environment that meets specific design requirements. The board also contains

LEDs and test points that provide a means of monitoring performance in real time.
The FRDM-KL25Z is mounted to Arduino connectors on the bottom of the

KITPF5200FRDMEVM board. The role of the FRDM-KL25Z is to manage I

2

C

communication between the KITPF5200FRDMEVM board and the GUI installed on the

PC.

4.2 KITPF5200FRDMEVM features

•

Banana 4 mm for power supply input

•

Banana 4 mm for switcher 1 and switcher 2

•

Selectable OTP or TBB mode

•

PGOOD, RESETBMCU and XFAIL pins

•

USB to I

2

C protocol for easy connection to software GUI

•

LEDs, green and red, that indicate signal or regulator status

•

LED blue to indicate that VDDOTP pin is set to 8.0 V (OTP burning voltage)

4.3 KITPF5200FRDMEVM featured components

Figure 1

 shows the location of key KITPF5200FRDMEVM components.

UM11723

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 8 December 2021

5 / 51

Summary of Contents for KITPF5200FRDMEVM




















































Reviews:

No comments