manualshive.com logo in svg

NXP Semiconductors Kinetis KE1xZ256, Reference Manual

Share
Download
NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 974

If the selected edge by channel (n) bits is detected at channel (n) input, then channel (n)
CHF bit is set and the channel (n) interrupt is generated (if channel (n) CHIE = 1). If the
selected edge by channel (n+1) bits is detected at channel (n) input and (channel (n) CHF
= 1), then channel (n+1) CHF bit is set and the channel (n+1) interrupt is generated (if
channel (n+1) CHIE = 1).

The C(n)V register stores the value of FTM counter when the selected edge by channel
(n) is detected at channel (n) input. The C(n+1)V register stores the value of FTM
counter when the selected edge by channel (n+1) is detected at channel (n) input.

In this mode, a coherency mechanism ensures coherent data when the C(n)V and C(n
+1)V registers are read. The only requirement is that C(n)V must be read before C(n
+1)V.

Note

• The channel (n)n CHF, channel (n) CHIE, channel (n)

MSA, channel (n) ELSB, and channel (n) ELSA bits are
channel (n) bits.

• The channel (n+1) CHF, channel (n+1) CHIE, channel (n

+1) MSA, channel (n+1) ELSB, and channel (n+1) ELSA
bits are channel (n+1) bits.

• The Dual Edge Capture mode must be used with channel

(n) ELSB:ELSA = 0:1 or 1:0, channel (n+1) ELSB:ELSA =
0:1 or 1:0 and the FTM counter in 

Free running counter

.

39.5.26.1 One-Shot Capture mode

The One-Shot Capture mode is selected when (DECAPEN = 1), and (channel (n) MSA =
0). In this capture mode, only one pair of edges at the channel (n) input is captured. The
channel (n) ELSB:ELSA bits select the first edge to be captured, and channel (n+1)
ELSB:ELSA bits select the second edge to be captured.

The edge captures are enabled while DECAP bit is set. For each new measurement in
One-Shot Capture mode, first the channel (n) CHF and channel (n+1) CHF bits must be
cleared, and then the DECAP bit must be set.

In this mode, the DECAP bit is automatically cleared by FTM when the edge selected by
channel (n+1) is captured. Therefore, while DECAP bit is set, the one-shot capture is in
process. When this bit is cleared, both edges were captured and the captured values are
ready for reading in the C(n)V and C(n+1)V registers.

Functional description

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

974

NXP Semiconductors

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands