manualshive.com logo in svg

NXP Semiconductors Kinetis KE1xZ256, Reference Manual

Share
Download
NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 610

WDOG_CS field descriptions (continued)

Field

Description

0

Watchdog disabled.

1

Watchdog enabled.

6

INT

Watchdog Interrupt

This write-once bit configures the watchdog to immediately generate an interrupt request upon a reset-
triggering event (timeout or illegal write to the watchdog), before forcing a reset. After the interrupt vector
fetch (which comes after the reset-triggering event), the reset occurs after a delay of 128 bus clocks.

0

Watchdog interrupts are disabled. Watchdog resets are not delayed.

1

Watchdog interrupts are enabled. Watchdog resets are delayed by 128 bus clocks from the interrupt
vector fetch.

5

UPDATE

Allow updates

This write-once bit allows software to reconfigure the watchdog without a reset.

0

Updates not allowed. After the initial configuration, the watchdog cannot be later modified without
forcing a reset.

1

Updates allowed. Software can modify the watchdog configuration registers within 128 bus clocks
after performing the unlock write sequence.

4–3

TST

Watchdog Test

Enables the fast test mode. The test mode allows software to exercise all bits of the counter to
demonstrate that the watchdog is functioning properly. See the 

Fast testing of the watchdog

 section.

This write-once field is cleared (0:0) on POR only. Any other reset does not affect the value of this field.

00

Watchdog test mode disabled.

01

Watchdog user mode enabled. (Watchdog test mode disabled.) After testing the watchdog, software
should use this setting to indicate that the watchdog is functioning normally in user mode.

10

Watchdog test mode enabled, only the low byte is used. CNT[CNTLOW] is compared with
TOVAL[TOVALLOW].

11

Watchdog test mode enabled, only the high byte is used. CNT[CNTHIGH] is compared with
TOVAL[TOVALHIGH].

2

DBG

Debug Enable

This write-once bit enables the watchdog to operate when the chip is in debug mode.

0

Watchdog disabled in chip debug mode.

1

Watchdog enabled in chip debug mode.

1

WAIT

Wait Enable

This write-once bit enables the watchdog to operate when the chip is in wait mode.

0

Watchdog disabled in chip wait mode.

1

Watchdog enabled in chip wait mode.

0

STOP

Stop Enable

This write-once bit enables the watchdog to operate when the chip is in stop mode.

0

Watchdog disabled in chip stop mode.

1

Watchdog enabled in chip stop mode.

Memory map and register definition

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

610

NXP Semiconductors

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands