NXP Semiconductors Kinetis KE1xZ256 Reference Manual Download Page 402 | Manualshive

Page: 402 / 1325

background image

SCG_LPFLLSTAT field descriptions (continued)

Field

Description

When LPFLL is enabled and auto trimming is enabled (LPFLLTREN=1 and LPFLLTRUP=1) these register
gets uploaded with the trimmed value. When LPFLLTRUP=0, these register is writeable to allow user
programming of trim values.

18.4 Functional description

18.4.1 SCG Clock Mode Transitions

The following figure shows the valid clock mode transitions supported by SCG.

Slow IRC (SIRC) boot mode is not supported on this device.

NOTE

When a transition between run modes (RUN, VLRUN) is
required, the SCG should complete the switch to the clock
mode as defined in the SCG clock control register first. Once
the switch to the clock mode is completed, the system can then
initiate the request for the selected run mode.

For example, if a transition from RUN mode to VLRUN is
required, first complete any required clock change. Initiate the
VLRUN request after the clock change has completed.

The power modes are chip specific. For more details about power mode assignments, see
power management and system mode control information.

The modes of operation listed in the following table are the valid modes for this
implementation of the SCG.

Table 18-1. SCG modes of operation

Mode

Description

System Oscillator Clock
(SOSC)

System Oscillator Clock (SOSC) mode is entered when all the following conditions occur:

• RUN MODE: 0001 is written to RCCR[SCS].

VLRUN MODE: 0001 is written to VCCR[SCS].

• SOSCEN = 1

• SOSCVLD = 1

In SOSC mode, SCGCLKOUT and system clocks are derived from the external System Oscillator
Clock (SOSC).

Table continues on the next page...

Functional description

Kinetis KE1xZ256 Sub-Family Reference Manual, Rev. 3, 07/2018

402

NXP Semiconductors

«
...
400
401
402
403
404
...
»

Summary of Contents for Kinetis KE1xZ256














































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Kinetis KE1xZ256

Brand: Gardena Pages: 18

VLT Micro Drive FC 51 Series

Brand: Danfoss Pages: 23

Brand: Talgil Pages: 14

Brand: Eaton Pages: 448

NOVASTAT EL DIGITAL

Brand: Taconova Pages: 7

Brand: Kampmann Pages: 5

1020 CAN-RS232-RS422 MFL

Brand: PENKO Pages: 29

Brand: Therma-Stor Pages: 20

Brand: Aqua Lung Pages: 24

Brand: Atmel Pages: 12

Brand: Unimig Pages: 4

Brand: Nibe Pages: 20

Brand: FASTRON. Pages: 37

Brand: Festo Pages: 2

Brand: E+L Pages: 62

Brand: Omicron Pages: 17

Brand: Simplex Pages: 12

fantech IPF05-1L

Brand: SystemAir Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands