manualshive.com logo in svg

NXP Semiconductors K22F series, Reference Manual, Page: 806 / 1407

Share
Download
NXP Semiconductors K22F series Reference Manual Download Page 806

34.4.10.1 Normal Stop mode with Bus Clock selected

If the Bus Clock is selected as the conversion clock, executing a stop instruction aborts
the current conversion and places the ADC in its Idle state. The contents of the ADC
registers, including Rn, are unaffected by Normal Stop mode. After exiting from Normal
Stop mode, a software or hardware trigger is required to resume conversions.

34.4.10.2 Normal Stop mode with ADACK or Alternate clock sources

enabled

If ADACK or an Alternate clock source is selected as the conversion clock, the ADC
continues operation during Normal Stop mode. See the chip-specific ADC information
for configuration information for this device.

If a conversion is in progress when the MCU enters Normal Stop mode, it continues until
completion. Conversions can be initiated while the MCU is in Normal Stop mode by
means of the hardware trigger or if continuous conversions are enabled.

If the compare and hardware averaging functions are disabled, a conversion complete
event sets SC1n[COCO] and generates an ADC interrupt to wake the MCU from Normal
Stop mode if the respective ADC interrupt is enabled, that is, when SC1n[AIEN]=1. The
result register, Rn, will contain the data from the first completed conversion that occurred
during Normal Stop mode. If the hardware averaging function is enabled, SC1n[COCO]
will set, and generate an interrupt if enabled, when the selected number of conversions
are completed. If the compare function is enabled, SC1n[COCO] will set, and generate an
interrupt if enabled, only if the compare conditions are met. If a single conversion is
selected and the compare is not true, the ADC will return to its idle state and cannot wake
the MCU from Normal Stop mode unless a new conversion is initiated by another
hardware trigger.

34.4.11 MCU Low-Power Stop mode operation

The ADC module is automatically disabled when the MCU enters Low-Power Stop
mode.

All module registers contain their reset values following exit from Low-Power Stop
mode. Therefore, the module must be re-enabled and re-configured following exit from
Low-Power Stop mode.

NOTE

For the chip specific modes of operation, see the power
management information for the device.

Functional description

K22F Sub-Family Reference Manual, Rev. 4, 08/2016

806

NXP Semiconductors

Summary of Contents for K22F series
































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments