manualshive.com logo in svg

NXP Semiconductors i.MX 6Dual, Reference Manual

Share
Download
NXP Semiconductors i.MX 6Dual Reference Manual Download Page 154

ERR004298

Chip Errata for the i.MX 6Dual/6Quad and i.MX 6DualPlus/6QuadPlus, Rev. 6.1, 06/2016

154

NXP Semiconductors 

 

Description:

Figure 3-15 in Section 3.5.2.2. “Handling of Received DLLPs” of the PCI Express base 
Specification 3.0, indicates when a bad DLLP error should be reported. It should occur when the 
calculated CRC is not equal to the received value. The core correctly reports a bad DLLP error 
under this scenario. However, it also sets it if the Physical Layer reports a packet error during 
reception of the DLLP or if the DLLP ends with an ENDB symbol and not an END symbol. These 
extra conditions should not result in the reporting of a bad DLLP error.

Projected Impact:

A bad DLLP error is reported when it should not be. However, in this scenario, the core has 
received a bad DLLP. There are no adverse side effects.

Workarounds:

None required, there are no adverse side effects.

Proposed Solution:

No fix scheduled

Linux BSP Status:

Software workaround cannot be implemented to mask or workaround this SoC issue. This erratum 
will result in impacted or reduced functionality as described above.

ERR004298

PCIe: 9000471173—Bad DLLP error status checking is too strict

Summary of Contents for i.MX 6Dual


































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands