manualshive.com logo in svg

Nuvoton NuMicro M0A21 Series, Technical Reference Manual

Share
Download
Nuvoton NuMicro M0A21 Series Technical Reference Manual Download Page 420

            M0A21/M0A23 Series 

 

May 06, 2022 

Page 

420

 of 746 

Rev 1.02 

M0

A21

/M
0

A

2

3

 SE
RIES

 TEC

H

NICAL 

RE
FEREN

C

E 
M

ANUAL

 

(UART_FIFOSTS),  and  line  control  register  (UART_LINE)  for  transmitter  and  receiver.  The  time-out 
register (UART_TOUT) identifies the condition of time-out interrupt.  

 Auto-Baud Rate Measurement 

This block is responsible for auto-baud rate measurement. 

 Interrupt Control and Status Register 

There  are  eleven  types  of  interrupts.  Interrupt  enable  register  (UART_INTEN)  enable  or  disable  the 
responding  interrupt  and  interrupt  status  register  (UART_INTSTS)  identifying  the  occurrence  of  the 
responding interrupt. 

Interrupt 

Description 

RDAINT 

Receive Data Available Interrupt. 

THERINT 

Transmit Holding Register Empty Interrupt. 

TXENDINT 

Transmitter Empty Interrupt. 

RLSINT 

Receive Line Status Interrupt (parity error or frame error or break error). 

MODEMINT 

MODEM Status Interrupt. 

RXTOINT 

Receiver Buffer Time-out Interrupt. 

BUFERRINT 

Buffer Error Interrupt. 

LININT 

LIN Bus Interrupt. 

WKINT 

Wake-up Interrupt. 

ABRINT 

Auto-Baud Rate Interrupt. 

SWBEINT 

Single-wire Bit Error Detect Interrupt. 

Table 6.11-2 UART Interrupt 

6.11.4  Basic Configuration 

The basic configurations of UART0 are as follows: 

 

Clock Source Configuration

 

– 

Select the source of UART0 peripheral clock on UART0SEL (CLK_CLKSEL1[26:24]).

 

– 

Select the clock divider number of UART0 peripheral clock on UART0DIV 
(CLK_CLKDIV0[11:8]).

 

– 

Enable UART0 peripheral clock in UART0CKEN (CLK_APBCLK0[16]).

 

 

Reset UART0 controller in UART0RST (SYS_IPRST1[16]).

 

 

Pin Configuration

 

Group 

Pin Name 

GPIO 

MFP 

UART0 

UART0_RXD 

PD.1, PD.5

 

MFP3 

PA.0, PA.1, PA.2, PA.3, PA.4, PA.5 

PB.4, PB.5, PB.6, PB.7 

PC.0,  PC.1,  PC.2,  PC.3,  PC.4,  PC.5,  PC.6, 
PC.7 

MFP9 

UART0_TXD 

PD.0, PD.4

 

MFP3 

PA.0, PA.1, PA.2, PA.4, PA.5 

MFP8 

Summary of Contents for NuMicro M0A21 Series











































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands