manualshive.com logo in svg

Nuvoton NUC970 series, Technical Reference Manual, Page: 19 / 1251

Share
Download
Nuvoton NUC970 series Technical Reference Manual Download Page 19

NUC970 Technical Reference Manual 

 

 

Publication Release Date: Dec. 15, 2015 

- 19 - 

Revision V1.30 

NUC97

0  
T

E

CHNIC

A

L 

RE

F

E

RE
N

CE
 MA
NUA

L

 

2 

FEATURES 

  NUC970 Series Features 

2.1

 

Core 

– 

ARM®  ARM926EJ-S

™ processor core runs up to 300 MHz 

– 

Support 16 KB instruction cache and 16 KB data cache 

– 

Support MMU 

– 

Support JTAG Debug interface 

 

External Bus Interface (EBI) 

– 

Support SRAM and external I/O devices 

– 

Support 8/16-bit data bus width 

– 

Support up to five chip selects for SRAM and external I/O devices 

– 

Support programmable access cycle 

– 

Support four 32-bit write buffers 

 

DDR SDRAM Controller 

– 

Support DDR, DDR2 and LPDDR SDRAM 

– 

Clock speed up to 150 MHz 

– 

Support 16-bit data bus width 

– 

Support two chip selects 

– 

Support total memory size up to 256M bytes (each chip select for 128M bytes) 

 

Embedded SRAM and ROM 

– 

Support 56K bytes embedded SRAM 

– 

Support 16K bytes Internal Boot ROM (IBR) 

– 

Support up to four booting modes 

– 

Boot from USB 

– 

Boot from eMMC 

– 

Boot from NAND Flash 

– 

Boot from SPI Flash 

 

Clock Control 

– 

Support two PLLs, up to 500 MHz, for high performance system operation 

– 

External 12 MHz high speed crystal input for precise timing operation 

– 

External 32.768 kHz low speed crystal input for RTC function and low speed clock 
source 

 

Ethernet MAC Controller 

– 

Support up to 2 Ethernet MAC controllers 

– 

Support IEEE Std. 802.3 CSMA/CD protocol 

– 

Support packet time stamping for IEEE Std. 1588 protocol 

– 

Support 10 and 100 Mbps operations 

– 

Support Half- and Full-duplex operations 

– 

Support RMII interface to Ethernet physical layer PHY 

– 

Support Ethernet physical layer PHY management through MDC and MDIO interface 

– 

Support flow control in Full-duplex mode to receive, recognize and transmit PAUSE 
frame 

– 

Support CAM-like function to recognize 48-bit Ethernet MAC address 

– 

Support Wake-On-LAN by detecting Magic Packet 

– 

Support 256 bytes transmit FIFO and 256 bytes receive FIFO 

– 

Support DMA function 

– 

Support internal loop back mode for diagnostic 

 

USB 2.0 Controller 

Summary of Contents for NUC970 series




































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments