manualshive.com logo in svg

NUVE NF 200, User Manual

Share
Download
NUVE NF 200 User Manual Download Page 16

 

 

15 

BÖLÜM 9 

– TROUBLESHOOTING 

If the centrifuge fails to operate, 

Check that, 

•

  The on/off switch is on, 

•

  The fuses are sound, 

•

  The plug is not defective, 

•

  The centrifuge is well connected to the supply, 

•

  The electricity installation is not defective, 

•

  Power is supplied.  

In case of below written failures, related error codes are shown. 

Error Codes  

In  case  of  below  written  failures,  related  error  codes  shown  on  the  speed  display,  motor 
starts braking.  

Err 3

: 

•

 

The communication between the display & main PCB and the motor driver PCB fails. 

Err 4:

 

•

 

Motor overheat failure. Please wait for the motor to cool down and start the centrifuge 
again.

  

Err 6

: 

•

 

Motor driver PCB is defective. 

Lid open

:  

•

 

This failure occurs when lid is opened during the centrifugation.  

•

 

Please close the lid properly and start the centrifuge again. 

Eoff

:  

•

 

It occurs in case of a power failure during the run. It dissapears if you wait for 2 minutes 
or open and close the lid again. 

 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for NF 200



















Reviews:

No comments

Brands by name

Popular brands

Load more brands