background image

 

Operating Instruction and Documentation 

                                                                                                                        

2.30 SPL                      

 

- 15 - 

 

4. Safety regulations 

 

When using automotive lifts the safety regulation EN1493/Aug.98 (CEN/TC 98 „ Automotive lifts”) 
must be observe adhered to. 

 
Especially the following regulations are very important: 
 

•  The laden weight of the lifted vehicle must not exceed 6500 kg for the automotive lift. 
•  The automotive lift must be in its lowest position (fully collapsed), before the vehicle can 

be driving on to the lift. Only then can the vehicle be lifted.  

•  While working with the lift the operating instructions must be followed. 
•  Vehicles with low clearance or vehicles that are specially equipped should be pre tested 

to ensure that they clear the lift ramp to avoid damage. 

•  Only trained personnel over the age of 18 years old are to operate this lift. 
•  No one is to stand within the working area (danger area) during lifting and lowering  
•  No one is to be raised or lowed either directly or in a vehicle by the automotive lift. 
•  No one is to climb onto the automotive lift or onto an already raised vehicle. 
•  The automotive column lift must be checked by an expert after changes in the 

construction have been made. 

•  The main switch must be switched off and locked before work on the vehicle can commence. This 

is a safety precaution to ensure that the lift does not move during work. 

•  The main switch must be switched off and locked before any maintenance or repair work 

on the automotive lift itself can be carried out. 

•  During lifting or lowering the operator must observe the vehicle to ensure that the vehicle 

and the lift are functioning correctly. 

•  Installation of the standard-mobile column lift in hazardous or dangerous locations such 

as washing bays is dangerous and is not allowed. 

•  Check the centre of gravity of the vehicle if heavy parts (eg the motor) are removed. 
•  If heavy parts must be removed (motor) the centre of gravity will change. Secure the 

vehicle before removing parts to avoid the possibility of the vehicle becoming insecure. 

 

 

 

5. Operating Instructions 

 

The Safety Regulations must be observed and adhered to while working with the 
automotive lift. Read the safety regulations in chapter 4 carefully before working with 
the lift! 

 

Pic. 1: Operational control 

 

 
 
  
 
 

A button “lifting” 
B lever “lowering” + button “unlocking the ratchets” 
C main switch 
 

 
 
 
 

Summary of Contents for 2.30 SPL











































Reviews: