NuAire MRXBOX95-LH2 Datasheet Download Page 1

   S U M M A R Y   F A N   D A T A   S H E E T

 
Nuaire Limited,  Western Industrial Estate,  Caerphilly,  CF83 1NA,  United Kingdom.    email:[email protected]
UK Technical Enquiries  Tel:029 2085 8200  Fax:029 2085 8300    International Enquiries  Tel:+44 29 2085 8335  Fax:+44 29 2085 8278

 
Whilst the information given on this data sheet is fan specific, it is in summary and reference to the product selection catalogue and installation & maintenance documents is recommended.
This data sheet produced on 22 Mar 2011 15:14 using software version 2.4.46 - 7 March 2011

0

0.02

0.04

0.06

0.08

0.1

0.12

0.14

700

600

500

400

300

200

100

0

Volume Flow Rate (m³/s)

Static Pressure (Pa)

Technical Data

MRXBOX95-LH2 - Loft Mounted Multi Room Xbox

Loft Mounted Multi-Room Heat Recovery Unit

Fan Code:

MRXBOX95-LH2

Installation Manual Links:

671496

Electrical Supply:

1 Phase

Motor Current:

flc: 2.1 A

Motor Current:

sc: 2.1 A

Max. Operating Temp.:

40°C

Weight:

21 kg

Sound Data

Acoustic perfomance to BS848 Part 2.2 and AMCA 300.
Breakout Noise (dBA): 51 dBA @ 3m
Inlet Noise (dBA): 43 dBA @ 3m
Outlet Noise (dBA): 58 dBA @ 3m
Breakout level is hemi-spherical. For spherical deduct 3 dBA.

Sound Power Levels re 1 pWatts (Hz):
Hz

63

125

250

500

1k

2k

4k

8k

Open Inlet(43%)

50

54

62

62

55

47

39

38

Open Outlet(58%)

56

65

72

77

69

69

61

54

Breakout(51%)

56

64

69

69

60

60

52

50

Above noise measured at stated percent of maximum working
pressure.

SAP Appendix Q Test Results

Application

Specific Fan
Power (W/l/s)

Heat Exchange
Efficiency %

E.S.T.* Best
Practice Compliant

K 1 wet room

0.81

91

Yes

K 2 wet rooms 0.77

91

Yes

K 3 wet rooms 0.78

91

Yes

K 4 wet rooms 0.86

91

Yes

K 5 wet rooms 0.96

91

Yes

K 6 wet rooms 1.09

90

No

* E.S.T. = Energy Saving Trust

Fan Dimensions

The drawing is for dimensional purposes only. Dimensions in mm.

Performance Curve

Summary of Contents for MRXBOX95-LH2










Reviews: