manualshive.com logo in svg

NSK Surgic Pro2, Operation Manual, Page: 38 / 55

Share
Download
NSK Surgic Pro2 Operation Manual Download Page 38

37

Setting

English

<Setting values of foot control button>

Setting 

value

Function

Press and release button

Press and hold button more than 2 seconds

0

Invalid

Invalid

1

Coolant solution flow level selection (up)

Switching operation between this product and 
linked device

2

Program number selection (up)

Program number selection (down)

3

Direction of rotation switching

Motor LED illumination while button is depressed
(Motor will not rotate)

4

Rotation speed setting (up)

Rotation speed setting (down)

5

Rotation speed setting (up)

Rotation speed setting (fast forward to up-direction)

6

Rotation speed setting (down)

Rotation speed setting (fast forward to down-direction)

7

Torque setting (up)

Torque setting (down)

8

Torque setting (up)

Torque setting (fast forward to up-direction)

9

Torque setting (down)

Torque setting (fast forward to down-direction)

A

Coolant solution flow level selection (up)

Coolant solution flow level selection (0:no coolant 
solution flow)

B

Program number selection (up)

Implant system selection (up)

C

Implant system selection (up)

Implant system selection (down)

D

Motor LED brightness selection

E

Motor LED illumination while button is depressed (Motor will not rotate)

F

Irrigation while button is depressed (Motor will not rotate)

8 – 2  Implant system

Eight programs can be set for each of the eight different implant systems�
When you set the program, refer to values the implant manufacturer recommends�

How to change implant system

Press the   and   on 

 simultaneously to change the implant system�

* Factory settings: See “11 – 8 Factory settings (Implant system)”�

Summary of Contents for Surgic Pro2
























































Reviews:

No comments