manualshive.com logo in svg

NR Electric PCS-9785, Instruction Manual, Page: 66 / 108

Share
Download
NR Electric PCS-9785 Instruction Manual Download Page 66

6 Settings 

 

PCS-9785 Satellite Synchronized-Clock

 

6-12 

Date: 2019-07-05 

6.3.7 Internal Clock Operation Mode 

If the operation mode of internal clock is "ON" (default) and there is no IRIG-B signal input, the 
time synchronization source will be the internal clock. Then, if one of the two inputs has received 
IRIG-B signal, the time source will be switched automatically. Additionally, the internal clock will be 
synchronized every minute. 

If the operation mode of internal clock is "OFF" and there is no IRIG-B signal input, there will be no 
time synchronization output from this device. 

  Command format: CD 

C   

 

 

 

The command key word 

D   

 

 

 

Internal clock operation mode, 1: ON; 0: OFF 

Example: C1 means the operation mode is ON. 

  Command format: C? 

To query the current internal clock operation mode. 

6.3.8 Input Channel Alarm Mode 

The two IRIG-B signal inputs can be adopted together or separately. The input channel alarm 
mode should be set according to the real adoption situation. 

  Command format: WD 

W   

 

 

 

The command key word 

D   

 

 

 

Input channel alarm mode 

0: alarm while one input channel is disconnected 

1: alarm while one input channel is disconnected or the time source is 
asynchronous (default) 

2: alarm while both input channels are disconnected 

  Command format: W? 

To query the current input channel alarm mode. 

 

 

08020

08020

08020

08020

08020

08020

08020

08020

08020

Summary of Contents for PCS-9785













































































































Reviews:

No comments