manualshive.com logo in svg

NR Electric PCS-9785, Instruction Manual, Page: 29 / 108

Share
Download
NR Electric PCS-9785 Instruction Manual Download Page 29

 

4 Supervision

 

PCS-9785 Satellite Synchronized-Clock

 

4-1 

Date: 2019-07-05 

4.1 Supervision Alarms

 

Hardware circuit and operation status of the device are self-supervised continuously. If any 
abnormal condition is detected, information or report will be displayed and a corresponding alarm 
will be issued. 

A minor abnormality may block a certain number of functions while the other functions can still 
work. However, if severe hardware failure or abnormality, such as PWR module failure, DC 
converter failure and so on, are detected, all functions will be blocked and the LED “

HEALTHY

” 

will be extinguished. The device then cannot work normally and maintenance is required to 
eliminate the failure. All the alarm signals and the corresponding handling suggestions are listed 
below. 

NOTICE! 

ONLY

 the master mode PCS-9785 clock source is equipped with a large scale LCD and 

the MON module for SAS communication. Thus the following alarms can be viewed 
locally from device LCD or remotely from SCADA. 

NOTICE! 

If the device is blocked or alarm signal is sent during operation, please do find out its 
reason with the help of self-diagnostic record. If the reason cannot be found at site, a 
trial recovery of the device by re-energization is suggested. Please contact the supplier 
if the device is still failure. 

Table 4.1-1 Alarm description 

No. 

Item 

Description 

1 

Fail_Device 

The MON module fails. The device fails. 

2 

Alm_Initialization 

Error is found during device initialization process and there will be no time 
synchronization output. 

3 

Alm_Device 

The device is abnormal. 
This signal will pick up if any other alarm picks up and it will drop off when all 
alarms drop off. 

4 

Alm_DualDev 

The device working mode "Master" or "Slave" is wrong. 
The CLK module type does not conform to the device configuration file. 

5 

Alm_Pwr1_Device 

The device power supply 1 fails. 

6 

Alm_Pwr2_Device 

The device power supply 2 fails. 

7 

Alm_Receiver_SatlCh1 

The receiver of satellite channel 1 fails. 

8 

Alm_Receiver_SatlCh2 

The receiver of satellite channel 2 fails. 

9 

Alm_SynLoss_SatlCh1 

The synchronization of satellite channel 1 is lost. 

10  Alm_SynLoss_SatlCh2 

The synchronization of satellite channel 2 is lost. 

11  Alm_Ant_SatlCh1 

The antenna of satellite channel 1 fails. 

12  Alm_Ant_SatlCh2 

The antenna of satellite channel 2 fails. 

13  Alm_Parity_IRIG-B1 

Error is found during the parity check of IRIG-B1 

08020

08020

08020

08020

08020

08020

08020

08020

08020

Summary of Contents for PCS-9785













































































































Reviews:

No comments