Novatel DL-V3 Reference Manual Download Page 65

Page: 65 / 116

DL-V3 Commands

Chapter 2

DL-V3 Firmware Reference Manual Rev 2

Table 46: SITEUPDATENUMBER Default Configuration

2.37 SITEUPDATENAME

Set Occupied Site Name

The

siteupdatename

command allows you to configure the site name information (SiteName field in

the

sitedef

log) once the site has been occupied (by issuing a

site enter

command).

The

siteupdatename

set

command sets the site name for an occupied site to

sitename.

The

siteupdatename

default

command sets the name to “SITE”

The

siteupdatename

clear

command has no effect

Syntax

siteupdatename

set

sitename

siteupdatename

default|clear

Message ID = 170

Table 47: SITEUPDATENAME Default Configuration

Parameter

Power-On

Freset

Stored in NVM

Site Number

clear

Field

Data

Value Used if

Not Specified

Bytes

Format

Units

Offset

Header

Parameter Update, see

Table 23 on Page 41

Enum

none

Site name

Char[]

none

H+4

Reserved for future use

NUL

Char[]

none

H+36

Parameter

Power-On

Freset

Stored in NVM

Site Name

clear

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands