Novatel DL-V3 Reference Manual Download Page 20

Page: 20 / 116

DL-V3 Firmware Reference Manual Rev 2

Chapter 2

DL-V3 Commands

Table 4: DL-V3 Commands in Order of their Message IDs

Message ID

ASCII Command

Description

reset

Perform a hardware reset

freset

Factory reset

del

Delete files from the CF Card

group

Modify log group definitions

groupantsn

Edit the serial number for the group

groupecutoff

Edit the elevation cut-off configuration for the group

groupmode

Configure the survey type for a group survey

groupfixpos

Fix the receiver position when the group is executed

groupsitename

Edit the site name for the group

groupsitenumber

Edit the site number for the group

groupsatlimit

Edit the satellite limit configuration for the group

grouppossave

Configure position averaging when the group is executed

grouplog

Modify message-logging specifications in a group

groupanttype

Edit the antenna type for the group

groupantheight

Edit the antenna height for the group

extcontrol

Disable POWERUP group execution on start-up

149

groupuse

Group configuration macro to execute DL-V3 commands

157

logfile

Manual file logging control

163

methumid

Specify air humidity

164

metpress

Specify air pressure

165

mettemp

Specify ambient temperature

166

site

Control site occupations

167

siteupdateantheight

Configure occupied site’s antenna height information

168

siteupdateanttype

Configure site antenna type information for an occupied site

169

siteupdateattribute

Configure site attribute information for an occupied site

170

siteupdatename

Configure site name information for an occupied site

171

siteupdatenumber

Configure site number information for an occupied site

185

currentfile

Specify a file for FILEHDR and FILETRANSFER requests

186

currentgroup

Specify a group for GROUPDEF requests

201

rename

Rename a file stored in the CF Card

Continued on Page 21

Summary of Contents for DL-V3





















































































































Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands

Novatel DL-V3, Reference Manual

Search results

Summary of Contents for DL-V3

Reviews:

Related manuals for DL-V3

Brands by name

Popular brands