10
AFP-3030 Operations Manual —
P/N DOC-01-033:C 05/12/2018
General Information
Message Formats
Point Events Format
When a change of state occurs to an SLC or panel point device, a message is generated to the panel that displays on the top of the LCD
screen, and soft keys display available functions that may be used to handle the event. The top four lines contain the event and point
information. Event counts display in the next three lines, the current time and soft key information appears after the event counts.
The format of the first line will vary slightly as follows, depending on the type of event.:
The second, third and fourth lines always contain the same device information, as follows:
The point event example screen below shows a fault condition that has been generated by the monitor on loop 2, address 4.
Figure 1.3 Point Event Display Example
The event counts display shows the counts for outstanding events. The date in line 16 gives the current time. The event keys may be used
to display events; their functions are described in the Operation section of this manual.
System Events Format
When a system fault occurs, a message is generated to the panel that displays on the top of the LCD screen, and soft keys display avail-
able functions that may be used to handle the event.
F I R E A L A R M
Z 0 0 1 : Z O N E Z 0 0 1
M O N I T O R
M o d u l e L 0 1 M 0 0 1
1 1 : 5 8 : 4 5 A T U E J A N 2 2 , 2 0 1 9
L 0 1 M 0 0 1
Line 1
Displays the type of
event, and whether
it has been
acknowledged or
cleared.
F A U L T
D E T E C T O R F A I L E D T E S T
Z 0 0 1 : Z O N E Z 0 0 1
M O N I T O R
M o d u l e L 0 1 M 0 0 1
1 1 : 5 8 : 4 5 A T U E J A N 2 2 , 2 0 1 9
L 0 1 M 0 0 1
Line 1
Displays FAULT,
the type of fault, and
whether it has been
acknowledged or
cleared.
Event
Format
(not fault or
prealarm)
Event
Format
(fault)
Line 1
Displays
PREALARM, the
sensitivity reading
and whether it has
been acknowledged
P R E A L A R M 1 2 0 % O F F I R E S E N S I T I V I T Y L E V E L 5
Z 0 0 1 : Z O N E Z 0 0 1
M O N I T O R
M o d u l e L 0 1 M 0 0 1
1 1 : 5 8 : 4 5 A T U E J A N 2 2 , 2 0 1 9
L 0 1 M 0 0 1
Event
Format
(prealarm)
F I R E A L A R M
Z 0 0 1 : Z O N E Z 0 0 1
M O N I T O R
M o d u l e L 0 1 M 0 0 1
1 1 : 5 8 : 4 5 A T U E J A N 2 2 , 2 0 1 9
L 0 1 M 0 0 1
Line 2 - Displays the custom
label and the extended label
Line 3 - Displays the primary
zone label, the primary zone
number, and the software
Type ID.
Line 4 - Displays event time,
event date and device
address.
Loop number
Detector
Device address
F A U L T : 3 O F 5
A C K N O W L E D G E D F A U L T
Z 0 0 1 : Z O N E Z 0 0 1
M O N I T O R
M o d u l e L 0 1 M 0 0 1
1 1 : 5 8 : 4 5 A T U E J A N 2 2 , 2 0 1 9
L 0 2 M 0 0 4
M O R E I N F O . . .
1
F L T L 0 1 M 0 0 1
M o d u l e L 0 1 M 0 0 1
2
F L T L 0 1 M 0 0 2
M o d u l e L 0 1 M 0 0 2
3
F L T L 0 1 M 0 0 4
M o d u l e L 0 2 M 0 0 4
A L M : 0
S U P : 0
F L T : 5
D I S : 0
O T H E R : 0
1 1 : 5 8 : 4 3 A T U E 0 2 , J A N , 2 0 1 9
