background image

FCC Statement

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a normal installation. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful 
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, 
the user is encouraged to try to correct the interference by one or more of the following measures:

  Reorient or relocate the receiving antenna.
  Increase the separation between the equipment and receiver.
  Connect the equipment into an output on a circuit different from that to which the receiver is connected.
  Consult the dealer or an experienced technician for help.
  A shielded cable must be used when connecting a peripheral to the serial ports.

Important

It is the owner’s sole responsibility to install and use the instrument and transducer/s in a manner that will not cause accidents, personal 
injury or property damage. The user of this product is solely responsible for observing safe boating practices. 
Northstar DISCLAIMS ALL LIABILITY FOR ANY USE OF THIS PRODUCT IN A WAY THAT MAY CAUSE ACCIDENTS, DAMAGE OR THAT MAY 
VIOLATE THE LAW.
This manual represents the NS3100 DEPTH as at the time of printing. Northstar reserves the right to make changes to specifications without 
notice.
Governing Language: This statement, any instruction manuals, user guides and other information relating to the product (Documentation) 
may be translated to, or has been translated from, another language (Translation). In the event of any conflict between any Translation of 
the Documentation, the English language version of the Documentation will be the official version of the Documentation. 
Copyright © 2005 Northstar.

Summary of Contents for NS 3100 DEPTH



















Reviews: