Northern N3NVR Series User Manual Download Page 86

Page: 86 / 218

Network Video Recorder
User Manual

UI System Setting

Issue: V4.6.X(2022-04-24)

7.2.3

RAID (Only for Some Models)

The NVR support to build/ edit/ delete the RAID. Users can choose the type of RAID according

to the importance of recording.

RAID is only used for the device with 4 disks or more. And the disks must be e

nterprise level disks.

The capacity of disks is the same for efficient using.

The maximum capacity of RAID cannot exceed 100T.

RAID5 at least 3 disks can be created. RAID6 at least 4 disks can be created. RAID10 at least 4

disks can be created. Create hot spare disk need more one disk or double basic disks.

The capacity of disks is the same for efficient using

Figure 7-16

RAID

Operation Steps

Step 1

Click

RAID

to create the RAID.

Step 2

Click

Create

to choose a disk to create a new RAID.

NOTE

Summary of Contents for N3NVR Series



























































































































































































































Search results

Summary of Contents for N3NVR Series

Reviews:

Brands by name

Popular brands

Northern N3NVR Series, User Manual

Search results

Summary of Contents for N3NVR Series

Reviews:

Brands by name

Popular brands