Northern N3NVR Series User Manual Download

Page: 41 / 218

Network Video Recorder

Basic Operations

User Manual

Issue: V4.6.X(2022-04-24)

Figure 4-5

Set question

The user can set three questions, and if they forget the password, they can answer the question and enter the

reset password interface.

Questions one can be set: Your favorite animal

Company name of your first job

The name of the first boy/girl you like

The worst security question you have ever seen

The most funny worst design you have ever seen

Your favorite team

Your favorite city

The three question options cannot be set to the same issue.

The answer requires a minimum of four characters and a maximum of 32 characters.

If you do not want to set a password question, you can click Skip this step.

4.3

Power off the Device

Click the main menu and choose

System

Maintenance

, the maintenance setting page is

displaying, click

Shutdown

to power off the NVR. If there is a power switch on the rear panel of

the NVR, you can power off the power switch to disconnect the NVR from the power supply.

Summary of Contents for N3NVR Series



























































































































































































































Search results

Summary of Contents for N3NVR Series

Reviews:

Related manuals for N3NVR Series

Brands by name

Popular brands

Northern N3NVR Series, User Manual

Search results

Summary of Contents for N3NVR Series

Reviews:

Related manuals for N3NVR Series

Brands by name

Popular brands