North American INVENTER SPLIT-TYPE ROOM AIR CONDITIONER Installation Manual Download | Manualshive

Page: 1 / 16

background image

Before using your air conditioner, please read

this manual carefully and keep it for future reference.

ROOM AIR CONDITIONER

Please read this installation manual completely
before installing the product.
If the power cord is damaged, replacement work
shall be performed by authorised personnel only.
Installation work must be performed in accordance
with the national wiring Standards by authorised
personnel only.
Contact an authorised service technician for
repair, maintenance or installation of this unit.

INVENTER SPLIT TYPE

-

1
2
3
...
»

Summary of Contents for INVENTER SPLIT-TYPE ROOM AIR CONDITIONER

















Reviews:

No comments

Related manuals for INVENTER SPLIT-TYPE ROOM AIR CONDITIONER

bycool DINAMIC 1.2

Brand: dirna Bergstrom Pages: 100

Brand: GE Pages: 36

Brand: Midea Pages: 104

Brand: Ramsond Pages: 15

AIRGOCLEAN 150 E

Brand: Trotec Pages: 13

Brand: PremierOne Pages: 7

Brand: GUTFELS Pages: 66

Brand: ARCTIC WIND Pages: 16

Brand: Innova Pages: 24

RXYQ16P7W1BA4 RXYQ18P7W1BA

Brand: Daikin Pages: 12

Brand: Zibro Pages: 18

Brand: TCL Pages: 43

Brand: Marstair Pages: 20

Brand: Olimpia splendid Pages: 28

Mr.Slim MSZ-A09NA

Brand: Mitsubishi Pages: 15

Brand: TriStar Pages: 48

Brand: MAXA Pages: 48

Brand: Argo Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands