Nortel RLC Installation And Administration Manual Download Page 96 | Manualshive

Page: 96 / 466

background image

70

RLC Installation and Administration Guide

Planning for RLC installation

Standard 4.0

Year 2000 compliance

The RLC and Configuration Manager software are Year 2000 compliant.
However, ensure the administration PC is Year 2000 compliant by verifying that
the Windows operating system meets the compliance requirement listed in the
following table:

Optivity Telephony Manager and Configuration Manager

Nortel does not guarantee that Optivity Telephony Manager (OTM) and the
Configuration Manager can operate simultaneously on the same administration
PC. Simultaneous running of these two applications has not been tested and is,
therefore, not supported.

Operating system

Year 2000 compliance requirement

Windows 95

Version 95b

Windows 98

OK as is

Windows NT Workstation 4.0

Service Pack 5 or higher

Windows 2000

Ok as is

Windows ME

Ok as is

Windows XP

OK as is

«
...
94
95
96
97
98
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Professional Series

Brand: PACOM Pages: 15

Brand: H3C Pages: 33

S5500-SI Series

Brand: H3C Pages: 1217

Brand: 3Com Pages: 2443

Brand: H3C Pages: 3

Brand: H3C Pages: 4

Brand: IEI Technology Pages: 21

Brand: JB Systems Pages: 24

Brand: JB Systems Pages: 61

Brand: SAF Pages: 30

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: Ubiquiti Pages: 3

Brand: WAGO Pages: 2

Brand: Commell Pages: 58

Brand: ETAS Pages: 69

Brand: Belkin Pages: 72

Brand: Helmholz Pages: 28

LBON320AC Series

Brand: Lindsay Broadband Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands