Nortel RLC Installation And Administration Manual Download Page 94 | Manualshive

Page: 94 / 466

background image

68

RLC Installation and Administration Guide

Planning for RLC installation

Standard 4.0

Ethernet connection

Configure the RLC’s IP interface information to allow calls to be routed
between the RLC and remote units. This also allows RLC administration to take
place over the IP network from a remote location.

Remote administration of the RLC means you can install the administration PC
in a location different from that of the RLC. Refer to the following illustration:

Administering multiple nodes

If you are responsible for administering the RLC on the host PBX and one or
more remote units, you can access the RLC and the remote unit from anywhere
on the network.

G031

RLC

Network

Host
PBX

Ethernet
network

Router

10.2.1.1

10.2.1.2

RLC
Administration
PC

10.2.1.10

10.4.1.2

«
...
92
93
94
95
96
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: D-Link Pages: 5

Brand: D-Link Pages: 2

Brand: B2 Pages: 52

Brand: Paradyne Pages: 45

Brand: NetBurner Pages: 15

BIC 1I12-P2A25-M30MI1-BPX05-110

Brand: Balluff Pages: 12

Brand: AOpen Pages: 18

Brand: Quantum Pages: 7

AT32F421 Series

Brand: ARTERY Pages: 337

Brand: Baikal Miner Pages: 14

Brand: 8e6 Technologies Pages: 94

Brand: Quatech Pages: 5

Brand: ZyXEL Communications Pages: 12

P-660R-F1 series

Brand: ZyXEL Communications Pages: 268

Brand: HALNy Pages: 12

Brand: Tripp Lite Pages: 2

Brand: Tripp Lite Pages: 2

Brand: GE Pages: 226

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands