Nortel RLC Installation And Administration Manual Download Page 72 | Manualshive

Page: 72 / 466

background image

46

RLC Installation and Administration Guide

RLC description

Standard 4.0

Command line interface

When the administration PC is connected to the RLC through the serial port, you
can view the command line interface using an application such as Telnet or
HyperTerminal. However, the command line interface is not documented in this
guide. Only use the command line interface with the assistance of technical
support personnel for troubleshooting and diagnostic testing. Configuration
Manager is the supported tool for customer administration of the RLC over both
the serial port and Ethernet connections. For further information, refer to “What
is Configuration Manager?” on page 126.

«
...
70
71
72
73
74
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: TC Electronic Pages: 2

Brand: Magnat Audio Pages: 2

Brand: Ubiquiti Pages: 23

Brand: Matrix Switch Corporation Pages: 61

Brand: Ruckus Wireless Pages: 56

Brand: Renesas Pages: 6

Brand: Cypress Semiconductor Pages: 11

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brand: NETGEAR Pages: 2

Brand: EnGenius Pages: 3

Brand: AMX Pages: 2

BiPAC 5200S RC Series

Brand: Billion Pages: 79

Brand: Telestar Pages: 16

Brand: ST Pages: 67

DTS 4020.timebridge

Brand: Mobatime Pages: 94

Brand: Stephen Pages: 8

Brand: Abus Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands