Nortel RLC Installation And Administration Manual Download Page 330

Page: 330 / 466

304

RLC Installation and Administration Guide

Troubleshooting

Standard 4.0

Network connectivity

This section identifies some problems that can occur on the network, and
describes what to do to resolve them.

Symptom descriptions

If you are not able to establish or maintain data network connectivity, perform
troubleshooting as described in the following table:

Symptom

What to do

You cannot establish a
connection from your
administration PC to the RLC.

Ensure that you entered the IP address
correctly when trying to establish the
connection.

Ensure that you entered the logon name
and password correctly when trying to
establish the connection.

Ensure the RLC’s IP address, network
mask, and default gateway are
configured correctly on the RLC.

PING the RLC.

PING the gateway.

If the PING still does not work, contact
your data network administrator.

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands