Nortel RLC Installation And Administration Manual Download Page 310 | Manualshive

Page: 310 / 466

background image

284

RLC Installation and Administration Guide

Administration

Standard 4.0

PSTN Error Statistics

PSTN Error Statistics allow you to see the PSTN performance, in terms of
signaling errors, of remote units connected to the logged-on RLC. Use these
statistics to indicate the effectiveness of your connection to the PSTN. The table
displays error totals for all active PSTN calls from the specified remote unit,
similar to the following.

Note:

PSTN Error Statistics are only available for Remote Gateway 9150 units.

«
...
308
309
310
311
312
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Samsung Pages: 2

Brand: Samsung Pages: 31

Brand: Samsung Pages: 15

Brand: M2M Pages: 9

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Brand: LORD Pages: 9

Brand: Profile Pages: 6

Brand: Allnet Pages: 12

Brand: Telebyte Pages: 19

Brand: NA Pages: 22

Teranex 2D Processor

Brand: Blackmagicdesign Pages: 969

Brand: Patton Pages: 62

Brand: VideoWave Pages: 12

Brand: Xantech Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands