Nortel RLC Installation And Administration Manual Download Page 309 | Manualshive

Page: 309 / 466

background image

RLC Installation and Administration Guide

283

June 2005

Administration

EthRx Mcast

Identifies the number of multicast packets that were
received during the given hour. This is inclusive of
packets with broadcast MAC addresses for protocols
such as ARP, and multicast packets for group-
oriented transmissions, such as IP Multicast.
Multicast packets are packets intended for more than
one Ethernet address.

EthRx UCast

Identifies the number of unicast packets that were
received during the given hour with a unicast
Ethernet address directly matching that of the
specified unit.
Unicast packets are packets intended for only one
Ethernet address.

EthRx Disc

Identifies the number of packets that were received
during the given hour and discarded due to a lack of
available receive buffers.

EthRx Err

Identifies the number of packets that were received
during the given hour that contained errors that
prevented them from being deliverable to a higher-
layer protocol.

Collisions

Identifies the number of collisions that have occurred

on the Ethernet interface when attempting to transmit

packets since the statistics were last reset.

Note:

The Collisions statistic appears on both the

Ethernet Interface and Network Statistics screens. It
is only applicable in half-duplex mode.

Statistic

Description

«
...
307
308
309
310
311
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: TC Electronic Pages: 2

Brand: Campbell Pages: 42

S5500-HI Switch Series

Brand: H3C Pages: 180

Brand: H3C Pages: 84

Brand: H3C Pages: 281

Brand: H3C Pages: 8

Brand: H3C Pages: 9

Brand: H3C Pages: 33

Brand: H3C Pages: 42

Brand: H3C Pages: 102

S12500CR Series

Brand: H3C Pages: 9

Brand: H3C Pages: 15

H3C S7500E Series

Brand: H3C Pages: 1565

Brand: H3C Pages: 4

Brand: IEI Technology Pages: 187

Brand: IEI Technology Pages: 71

Brand: YASKAWA Pages: 68

HAWA-Frontside 60/B

Brand: hawa Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands