Nortel RLC Installation And Administration Manual Download Page 300 | Manualshive

Page: 300 / 466

background image

274

RLC Installation and Administration Guide

Administration

Standard 4.0

Ethernet Interface Statistics field descriptions

The following table describes the statistics on the Ethernet Interface Statistics
screen:

Statistic

Description

Channel

Identifies the Ethernet device that the statistics on that
line apply to.
Valid values are 1 and 2.

LAN Drv

Identifies the LAN driver used by the call.

Admin

Identifies the desired state of the port.

Oper

Identifies the actual state of the port.

IfcType

Identifies the interface type used by the call.

IfcNo

Identifies the Ethernet interface used by the call.
Valid values are 0 (ELAN) and 1 (CLAN).

MTUlen

Identifies the Maximum Transmission Unit for this
interface in bytes.

Speed

Identifies the data rate of this interface in Mbps.

Rx Octet

Identifies the number of bytes received on the given
channel since the statistics were last reset.

Rx Ucast

Identifies the number of packets with a unicast Ethernet
address that directly matches the Ethernet address of the
identified unit. This statistic describes the period of time
since the statistics were last reset.

Rx Mcast

Identifies the number of multicast packets received.
These packets can be broadcast MAC addresses for
protocols such as ARP, as well as multicast packets for
group-oriented transmissions such as IP Multicast. This
statistic describes the period of time since the statistics
were last reset.

«
...
298
299
300
301
302
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Panasonic Pages: 18

Brand: Netopia Pages: 38

Brand: Konica Minolta Pages: 38

Brand: Western Digital Pages: 8

Brand: Google Pages: 14

ION 1200 Series

Brand: PaloAlto Networks Pages: 90

Brand: iBall Baton Pages: 9

RUGGEDMAX WIN7000

Brand: RuggedCom Pages: 42

Brand: Speedtouch Pages: 124

Brand: 3Com Pages: 50

Brand: Advantech Pages: 36

Brand: Supersonic Pages: 46

EK-FC285 GTX Classified

Brand: ekwb Pages: 2

SteelCentral AppResponse 2180

Brand: Riverbed Pages: 82

UniFi WiFi BaseStation XG

Brand: Ubiquiti Pages: 19

Emotron OSTO 100

Brand: CG Pages: 112

Brand: ZALMAN Pages: 9

Brand: Corsair Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands