Nortel RLC Installation And Administration Manual Download Page 294 | Manualshive

Page: 294 / 466

background image

268

RLC Installation and Administration Guide

Administration

Standard 4.0

Digital Signal Processor (DSP) Statistics

Digital Signal Processor (DSP) Statistics provide information about the DSP
application modules installed on the logged-on RLC. Use this screen to
determine the module positions that are populated, what type of DSP those
positions contain, and the functionality provided by each module. The DSP
Statistics screen is similar to the following:

To display the DSP Statistics screen, refer to “Displaying the DSP Statistics
screen” on page 269. To obtain the definitions for the statistics presented on the
DSP Statistics screen, refer to “DSP Statistics field descriptions” on page 270.

«
...
292
293
294
295
296
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Omnia Pages: 102

Brand: Udoo Pages: 7

Brand: F-SECURE Pages: 19

NetStructure ZT 5515

Brand: Intel Pages: 90

Brand: Opengear Pages: 2

Nighthawk M6 Pro

Brand: AT&T Pages: 2

Parallel & Serial Port Checker PPC

Brand: B&B Electronics Pages: 4

Brand: Maipu Pages: 80

LinkStation Mini

Brand: Buffalo Pages: 71

BROADCAST POLLING FRAD BPF-14 BU

Brand: DCB Pages: 28

Brand: Supermicro Pages: 15

Brand: ETAS Pages: 84

Brand: Laser Pages: 4

Wisenet XRN-6410RB2-24TB

Brand: Hanwha Techwin Pages: 124

Brand: ACTi Pages: 12

Brand: Airlinkplus Pages: 24

Brand: Behringer Pages: 15

Brand: ICP DAS USA Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands