Nortel RLC Installation And Administration Manual Download Page 293 | Manualshive

Page: 293 / 466

background image

RLC Installation and Administration Guide

267

June 2005

Administration

Hardware Statistics field descriptions

The following table describes the statistics on the Hardware Statistics screen:

Statistic

Description

Module No

Identifies the DSP application module’s position on
the RLC’s motherboard.

Status

Identifies whether there is a functional DSP
application module in the position identified in the
Module No field.
Valid values are Equipped and Unequipped.
Equipped means that a DSP application module is
installed in the module position and Unequipped
means that there is not a DSP application module
installed in the module position.

Module Type

Identifies the part number of the hardware installed
in the module position.

Version

Identifies the version of DSP application module
installed in the module position.

«
...
291
292
293
294
295
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Accelerated Pages: 10

Brand: Accelerated Pages: 4

Brand: Acconeer Pages: 32

Brand: Qlogic Pages: 2

Brand: Qlogic Pages: 172

EK-FC780 GTX Jetstream

Brand: ekwb Pages: 2

Brand: Conceptronic Pages: 230

Brand: Maxim Pages: 14

X-Pedition 2000

Brand: Enterasys Pages: 86

Brand: NETGEAR Pages: 84

Brand: Softing Pages: 4

AAA-130SA SERIES

Brand: Adaptec Pages: 94

Brand: Disc Makers Pages: 38

Brand: Renesas Pages: 746

Brand: IEI Technology Pages: 2

Brand: Xantech Pages: 5

Brand: Chase Research Pages: 114

Brand: Omron Pages: 432

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands