Nortel RLC Installation And Administration Manual Download Page 244 | Manualshive

Page: 244 / 466

background image

218

RLC Installation and Administration Guide

Configuring the RLC

Standard 4.0

How the remote site goes online

When going offline, the remote unit’s offline timer activates. When the timer
expires, the remote unit automatically initiates a “going online” request to the
host PBX. If the RLC receives the request successfully, the remote site and its
associated digital telephones go online.

If you configure no online entries in the online/offline table, the RLC instructs
the remote unit to go offline forever each time it processes an offline entry. To
go back online, a remote user must enter the online SPRE code in order to place
host-controlled calls on either the PSTN or IP network.

«
...
242
243
244
245
246
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: D-Link Pages: 100

Brand: D-Link Pages: 134

Brand: D-Link Pages: 187

Brand: D-Link Pages: 225

Brand: D-Link Pages: 31

Brand: D-Link Pages: 35

DES-1016D - Switch

Brand: D-Link Pages: 19

Brand: D-Link Pages: 107

AirPlusXtremeG DI-624

Brand: D-Link Pages: 5

Brand: D-Link Pages: 48

Brand: ICP DAS USA Pages: 48

Brand: ICP DAS USA Pages: 24

Brand: ICP DAS USA Pages: 4

Brand: Jabra Pages: 15

Brand: N-Tron Pages: 62

InterReach Fusion ADCP-77-044

Brand: TE Connectivity Pages: 236

Brand: Teac Pages: 20

cMT-FHDX Series

Brand: Maple Systems Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands