Nortel RLC Installation And Administration Manual Download Page 211 | Manualshive

Page: 211 / 466

background image

RLC Installation and Administration Guide

185

June 2005

Configuring the RLC

Prioritizing voice traffic over shared networks

Prioritizing voice traffic on shared networks can improve QoS on LAN and
WAN segments of the network that support prioritization. Achieving the desired
QoS through prioritization over LAN connections requires you to enable 802.1Q
Mapping. Achieving the desired QoS through prioritization over WAN
connections requires you to enable the DiffServ CodePoint.

For more information on DiffServ, 802.1Q, and quality of service in general,
refer to “Evaluating your network”, and “Quality of service issues” in the

Remote Gateway 9100 Series Network Engineering Guidelines

(NTP 555-8421-

103).

Full Duplex Ethernet

This setting configures Ethernet support on the RLC to allow
simultaneous transmission and reception of Ethernet packets.
When you enable full-duplex Ethernet, you must also set the
corresponding port on the connected switch, hub, or router to 10
FULL Duplex. Remote Gateway 9100 Series products do not
support Auto negotiation of the Ethernet interface.

Click on the

Enable

option button if you want to allow 10-

Megabit per second transmission in both directions, send
and receive.

Click on the

Disable

option button if you do not want to

allow 10-Megabit per second transmission in both
directions, send and receive.

The default is Disable.

Note:

When you configure a full-duplex Ethernet connection,

the RLC's Ethernet collision LED remains on solid (constantly
lit).

Field

Description

«
...
209
210
211
212
213
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Watchguard Pages: 40

Brand: Laird Pages: 36

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Brand: Harmonic Pages: 56

Brand: Paradyne Pages: 1

Brand: VMIC Pages: 126

Brand: Barco Pages: 121

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Brand: EMCIS Pages: 14

RabbitCore RCM4400W

Brand: Rabbit Pages: 126

ControlPoint 2000

Brand: 4Home Pages: 20

Brand: East Coast Datacom Pages: 19

Brand: Baicells Pages: 10

Brand: ActionTec Pages: 115

CNPS11X Extreme

Brand: ZALMAN Pages: 12

OMB-DAQBOARD-500 Series

Brand: Omega Pages: 48

Brand: netsys Pages: 164

Brand: Spirent Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands