Nortel RLC Installation And Administration Manual Download Page 201 | Manualshive

Page: 201 / 466

background image

RLC Installation and Administration Guide

175

June 2005

Configuring the RLC

Advanced
Configuration

Click on the

Advanced Configuration

button to display the

Advanced Configuration dialog box. From this dialog box, you
can to configure the following settings for the RLC:

Dialtone/DTMF Relay to configure whether the PBX or the
Remote Gateway 9100 Series unit generates the dial tone
and DTMF (button-press) tones

Non-Linear Processing (NLP) to configure echo
cancellation settings for calls supported by your Remote
Gateway 9100 Series system

For more information, refer to “Advanced configuration
settings” on page 169.

Trunk Support

Configure the speed of your Remote Gateway 9100 Series
connection as follows:

Choose

56K

if the speed of your Remote Gateway 9100

Series connection is 56 Kbps.

Choose

64K

if the speed of your Remote Gateway 9100

Series connection is 64 Kbps.

Choose

Dynamic

if your Remote Gateway 9100 Series

connection includes speeds at 56 Kbps and 64 Kbps.

Note:

You must configure the same BRI speed (such as 56K,

64K, or dynamic) on both the RLC and the Remote Gateway
9150 unit.

The default is 64K.

DSP Gain

Select the number of decibels (dB) that you want to add to, or
subtract from, the strength of the transmitted signal before the
DSP processes it.
Valid options are 9, 6, 3, 0, -3, -6, -9, -12, and -15.
The default is 0 dB.

Note:

Change this setting at the Host site to address a problem

with signal strength at the remote site.

Field

Description

«
...
199
200
201
202
203
...
»

Summary of Contents for RLC



















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RLC

Brand: Wattle Pages: 6

Brand: Baicells Pages: 8

Brand: Paradyne Pages: 2

Brand: Paradyne Pages: 20

Brand: Paradyne Pages: 2

Brand: Zhone Pages: 2

Brand: Zonet Pages: 10

Brand: Samsung Pages: 65

Brand: IBM Pages: 63

Brand: Qlogic Pages: 2

IntroSpect Analyzer 2 Series

Brand: Aruba Pages: 5

Brand: SeaLevel Pages: 21

Brand: Zoom Pages: 31

netHOST NHST-T100

Brand: hilscher Pages: 75

Brand: Xcellon Pages: 24

i.LON SmartServer

Brand: Echelon Pages: 34

Brand: ADTRAN Pages: 2

Brand: Aim Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands