Nortel RLC Installation And Administration Manual Download Page 124

Page: 124 / 466

RLC Installation and Administration Guide

Installing the RLC

Standard 4.0

The following is a completed example:

Click on the

Next

button.

Result:

The Set the Remote Unit information dialog box displays. A

completed example is shown on page 101.

Enter the Local IP
Mask of the unit

Enter the subnet mask.

Note:

The system requires that you enter an IP

address. If you are using PSTN only, enter the
following:

255.255.0.0

Enter the Local IP
Gateway of the unit

Enter the IP address of the gateway between
the RLC and the network.

Note:

The system requires that you enter an IP

address. If you are using the PSTN only, enter

1.2.3.5.

as both the IP address on the

administration PC and gateway on the RLC.

Field

Description

The IP information
allows you to administer
the RLC from any
location on the network.

Summary of Contents for RLC



















































































































































































































































































































































































































































































Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands

Nortel RLC, Installation And Administration Manual

Search results

Summary of Contents for RLC

Reviews:

Related manuals for RLC

Brands by name

Popular brands