manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 89 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 89

Removing a module

89

On a 8003, 8006, or 8010 chassis, the filler panel covers an empty module
slot. On the 8010co chassis, the filler panel resembles a module and is
installed in the empty module slot.

Installing a filler panel takes approximately one minute.

Procedure steps

Step

Action

1

Locate the slot where you want to install the filler panel.

2

Insert the filler panel into the slot (8010co chassis), or place the
filler panel over the slot (8003, 8006, or 8010 chassis).

3

Use a Phillips screwdriver to tighten the two screws.

--End--

Removing a module

Remove a module to install another module or a filler panel. Removing a
module takes three to five minutes.

Prerequisites

•

Before you remove an 8691 or 8692 SF/CPU module, back up your
configuration. If the chassis includes only one SF/CPU module and you
remove it, the switch does not operate.

•

Ensure that traffic is not traversing the module. Disable the
module before you remove it. For further instructions, see Nortel
Ethernet Routing Switch 8600 Configuration — Ethernet Modules,
NN46205-503.

WARNING

Risk of eye injury by laser

Fiber optic equipment can emit laser or infrared light that can
injure your eyes. Never look into an optical fiber or connector
port. Always assume that fiber optic cables are connected to a
light source.

CAUTION

Risk of equipment damage

Electrostatic discharge can damage hardware. Follow ESD
procedures to protect your equipment from damage.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments