manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 76 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 76

76

Ethernet Routing Switch 8600 module fundamentals

Table 27
8692 SF/CPU module LEDs (cont’d.)

Label

Color, State

Meaning

Green, Steady

The specified power supply is operating
normally.

Amber, Steady

The specified power supply failed.

Power Supply 1, 2, 3

Off

A power supply is not present in the specified
bay, or the power supply in the specified bay is
not turned on.

Green, Steady

The specified fan is operating normally.

Amber, Steady

The specified fan is present in the chassis and
has failed, or no fan is present in the chassis
and should be present.

Fan 1, 2

Off

The specified fan is not present in the chassis
(and should not be present).

Green, Steady

The CPU subsystem on the module is
performing diagnostics.

Green, Blinking

This module is providing active CPU functions
for the switch and is the Master CPU module.

Amber, Steady

The CPU subsystem is in a fault state.

Master

Off

The CPU subsystem on the module is up and
in Standby mode.

Green, Steady

The switch fabric portion of the module is online
and is load-sharing.

Amber, Steady

The switch fabric portion of the module failed
diagnostics.

Online

Off

The switch fabric portion of the module is offline.

8692 SF/CPU Ethernet management port

The Ethernet management port on the 8692 SF/CPU module is a Medium
Dependent Interface (MDI) 10/100BASE-T port that allows out-of-band
management of the switch using a Web browser or Device Manager. You
can also establish a Telnet or SSH (Secure Shell) session to access the
CLI. Use this port to connect the switch to a network management station.
The Ethernet management port has its own IP address, but does not
switch traffic to other ports in the chassis.

This port can be used only as a management port. This port provides
out-of-band management for the 8692 SF/CPU module.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments