manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 59 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 59

Interface module descriptions

59

RS modules are not compatible with the 8001AC and 8002DC power
supplies or the 8691 SF/CPU modules. You must use the 8692 SF/CPU
in chassis that contain RS modules. RS modules interoperate with
R modules.

The 8634XGRS module supports Custom Auto-Negotiation
Advertisements (CANA). For more information about CANA, see Nortel
Ethernet Routing Switch 8600 Configuration — Ethernet Modules,
NN46205-503.

The following figure shows the LED locations.

Figure 31
8634XGRS module LEDs

The following tables describe the 8634XGRS module LEDs.

Table 16
8634XGRS module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The module has completed the
power-on self-test and software
initialization and is operating normally.

Amber, Steady

The module is booting.

Amber, Blinking

The module failed to boot.

Module

Online

Off

The module power is off.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments