manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 57 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 57

Interface module descriptions

57

RS modules are not compatible with the 8001AC and 8002DC power
supplies or the 8691 SF/CPU modules. You must use the 8692 SF/CPU
in chassis that contain RS modules. RS modules interoperate with
R modules.

All RS modules support jumbo frames.

The following figure shows the LED locations.

Figure 29
8612XLRS module LED locations

The Port Status LEDs are below the port number label. The following table
describes the 8612XLRS module LEDs.

Table 15
8612XLRS module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is connected and linked, but
no data flow.

Green, Blinking

The port is transmitting or receiving
data. The blink rate indicates the level
of link activity.

Amber, Blinking

The port detects a Line or Remote
fault.

Amber, Steady

The port is administratively disabled.

Port

Port status (no
label)

Off

The port is connected but not linked.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments