manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 44 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 44

44

Ethernet Routing Switch 8600 module fundamentals

Both the 8648TXE and 8648TXM module ports support the IEEE 802.3
1998 Clause 28 Auto-Negotiation standard. Each port can operate in full-
or half-duplex mode. When a port is connected to another device that also
supports the IEEE 802.3 1998 Clause 28 Auto-Negotiation standard, the
two devices negotiate the highest possible data rate and the duplex mode
of operation.

The following figure shows the location of the 8648TXE and 8648TXM
module LEDs.

Figure 17
8648TXE and 8648TXM module LEDs

The following table describes the 8648TXE and 8648TXM module LEDs.

Table 8
8648TXE and 8648TXM module LEDs

Type

Label

Color, State

Meaning

Green, Steady

The port is operating at 100 Mbps.

10/100

Off

The port is operating at 10 Mbps.

Green, Steady

The port is connected and the link is
operational.

Green, Blinking

Data is passing through the port.

Port

Link/Activity

Off

The port is disabled or has no link.

Green, Steady

The module has completed the power-on
self-test and software initialization and is
operating normally.

Amber, Steady

The module failed the power-on self-test.

module

Online

Off

The module power is off. If the switch
power is on, the module is performing
the power-on self-test and software
initialization. A module in this state is not
yet functional.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments