Nortel Passport 8600 Series Installation Manual Download Page 140

Page: 140 / 164

140

Technical specifications

Table 80
WSM specifications (cont’d.)

Cable specifications

Minimum Receiver Sensitivity:

-17 dBm

Maximum Input Power:

0 dBm

Table 81
Pin assignments: WSM management port

Connector

Pin number

Signal

Input receive data + (RX+)

Input receive data – (RX–)

Output transmit data + (TX+)

Output transmit data – (TX–)

4, 5, 7, 8

Not used

Table 82
Maintenance port pin assignments for WSM

Connector

Pin number

Signal

WSM TxD to host RxD

Serial ground

Host TxD to WSM RxD

1,2,6,7,8

Not used

8691 SF/CPU module

The following table describes the 8691 SF/CPU module specifications.

Table 83
8691 SF/CPU module specifications

Physical specifications

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 140 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: