Nortel Passport 8600 Series Installation Manual Download Page 138

Page: 138 / 164

138

Technical specifications

Table 77
8660 SDM power specifications

Specification

Value

3.3 V power (W)

64.4

12 V power (W)

75.6

Total power (W)

140.0

8661 SAM

The following table describes the SSL Acceleration Module (SAM)
specifications.

Table 78
8661 SAM

Item

Specification

Height:

1.5 in. (3.8 cm)

Width:

15.4 in. (39.1 cm)

Depth:

18.5 in. (47.0 cm)

Weight:

14.0 lb (6.4 kg)

Electrical specifications

MTBF rating:

288 615 hours @ 25 C

Input power:

80 W maximum

Operating temperature:

0 to 40 C

Storage temperature:

-40 to 70 C

Maintenance port:

8-pin mini-DIN

Table 79
Maintenance port pin assignments for 8661 SAM

Connector

Pin number

Signal

SAM TxD to host RxD

Serial ground

Host TxD to SAM RxD

1,2,6,7,8

Not used

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 138 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: