Nortel Passport 8600 Series Installation Manual Download Page 127

Page: 127 / 164

8672ATME and 8672ATMM modules

127

Table 56
ATM module specifications (cont’d.)

Cable specifications

Maximum distance

Multimode fiber optic cable:

1.24 mi (2 km) for OC-3c
connection

1640 ft (500 m) for OC-12c
connection

single mode fiber optic cable:

9.3 mi (15 km) for OC-3c
connection

9.3 mi (15 km) for OC-12c
connection

Coaxial cable: 450 ft (137 m) for DS-3
connection

Optical specifications

Wavelength

OC-3c MDA SMF: 1274 to 1356 nm

OC-3c MDA MMF: 1274 to 1356 nm

OC-12c MDA SMF: 1274 to 1356 nm

OC-12c MDA MMF: 1260 to 1360 nm

Average transmit output power

OC-3c and OC-12c MDAs SMF: -8 to
-15 dBm

OC-3c and OC-12c MDAs MMF: -14 to
-29 dBm

Average receiver sensitivity

OC-3c MDA SMF: -14 to -28 dBm

OC-3c MDA MMF: -14 to -29 dBm

OC-12c MDA SMF: -7 to -18 dBm

OC-12c MDA MMF: -14 to -28 dBm

The following table provides power specifications.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Summary of Contents for Passport 8600 Series































































































































































Search results

Summary of Contents for Passport 8600 Series

Reviews:

Nortel Passport 8600 Series, Installation Manual, Page: 127 / 164

Search results

Summary of Contents for Passport 8600 Series

Reviews: