manualshive.com logo in svg

Nortel Passport 8600 Series, Installation Manual, Page: 116 / 164

Share
Download
Nortel Passport 8600 Series Installation Manual Download Page 116

116

Technical specifications

Table 33
Module specifications (cont’d.)

Address database size

64 to 9600 bytes (8608GBE,
8608GBM, 8608GTE, 8608GTM
modules only with Release 3.3 or
later)

64 to 9600 bytes (R series modules
with Release 4.0 or later)

The following table describes electromagnetic interference specifications.

Table 34
Electromagnetic interference specifications

Electromagnetic emissions

Meets requirements of:

US:

FCC CFR47 Part 15, Subpart B,
Class A

Canada:

ICES-003, Issue-2, Class A

Australia/New Zealand:

AS/NZS 3548:1995, Class A

Japan:

VCCI-V3/97.04, Class A

Taiwan:

CNS 13438, Class A

Europe:

EN 55022-1998 Class A; EN
61000-3-2/A14, EN 61000-3-3

Global:

CISPR 22-1997 Class A
CE Mark

Electromagnetic susceptibility:

EN55024:1998/CISPR 24:1997

The following table describes safety agency approvals.

Table 35
Safety agency approvals

Safety agency approvals

US:

UL60950

Canada:

CSA 22.2 No. 60950

Australia/New Zealand:

AS/NZS 3260

Mexico:

NOM-019-SCFI-1998

The Gigabit Ethernet transceivers installed in the 8608GBE and 8608GBM
modules must also meet the standards listed in the preceding table. In
addition, the Gigabit Ethernet transceivers are certified to FDA requirement
21 CFR, section 1, Subsection J and the international requirements of IEC
60825 for Class 1 Laser.

Nortel Ethernet Routing Switch 8600

Installation — Modules

NN46205-304

02.02

Standard

16 June 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for Passport 8600 Series





































































































































































Reviews:

No comments