manualshive.com logo in svg

Nortel Passport 7400, Hardware Installation, Maintenance, And Troubleshooting, Page: 353 / 438

Share
Download
Nortel Passport 7400 Hardware Installation, Maintenance, And Troubleshooting Download Page 353

Chapter 37 Hardware procedures   353

Passport 7400 Hardware Installation, Maintenance, and Upgrade 5.2S1

Removing a 16-slot Passport switch power supply

Remove a 16-slot Passport switch power supply if it fails.

Prerequisites

Procedure steps

1

Set the power switch on the power supply faceplate to the standby
position. See the figure “Unlocked power supply with power switch in the
standby position” (page 355).

CAUTION

Risk of service loss

Do not overload the power supplies. One power supply
can support a maximum of eight CPs and FPs.

WARNING

Risk of personal injury

Power supplies weigh 6.6 kg (14.5 lb) each. Handle
carefully and avoid dropping.

WARNUNG

Verletzungsgefahr

Die Stromversorgungsgeräte haben ein Gewicht von
jeweils 6,6 kg. Seien Sie vorsichtig beim Umgang mit
dem Gerät, und vermeiden Sie, es fallenzulassen.

WARNING

Damage to equipment by electromagnetic interference

To meet electromagnetic interference (EMI) regulatory
requirements and thermal specifications, empty power
supply bays must be fitted with power supply blanks.
Power supply blanks are removed and installed using the
same procedure as for power supplies.

Summary of Contents for Passport 7400























































































































































































































































































































































































































































Reviews:

No comments