manualshive.com logo in svg

Nortel BSR222, Configuration, Page: 117 / 451

Share
Download
Nortel BSR222 Configuration Download Page 117

Chapter 7 WAN screens

117

Nortel Business Secure Router 222 Configuration — Basics

RIP Direction

With RIP (Routing Information Protocol), a router can exchange 
routing information with other routers. The 

RIP Direction

 field 

controls the sending and receiving of RIP packets. 

Choose 

Both

, 

None

, 

In Only

 or 

Out Only

.

When set to 

Both

 or 

Out Only

, the Business Secure Router 

broadcasts its routing table periodically. 

When set to 

Both

 or 

In Only

, the Business Secure Router 

incorporates RIP information that it receives.

When set to 

None

, the Business Secure Router does not send any 

RIP packets and ignores any RIP packets received. 

By default, 

RIP Direction

 is set to 

Both

.

RIP Version

The 

RIP Version

 field controls the format and the broadcasting 

method of the RIP packets that the Business Secure Router sends 
(it recognizes both formats when receiving). 

Choose 

RIP-1

, 

RIP-2B

 or 

RIP-2M

.

RIP-1

 is universally supported; but 

RIP-2

 carries more information. 

RIP-1 is probably adequate for most networks, unless you have an 
unusual network topology. Both 

RIP-2B

 and 

RIP-2M

 sends the 

routing data in RIP-2 format; the difference being that RIP-2B uses 
subnet broadcasting while RIP-2M uses multicasting. Multicasting 
can reduce the load on nonrouter machines since they generally do 
not listen to the RIP multicast address and so do not receive the 
RIP packets. However, if one router uses multicasting, then all 
routers on your network must use multicasting, also. By default, the 

RIP Version

 field is set to 

RIP-1

.

Multicast

Choose 

None

 (default), 

IGMP-V1

 or 

IGMP-V2

. IGMP (Internet 

Group Multicast Protocol) is a network layer protocol used to 
establish membership in a Multicast group—it is not used to carry 
user data. IGMP version 2 (RFC 2236) is an improvement over 
version 1 (RFC 1112) but IGMP version 1 is still in wide use. If you 
want to read more detailed information about interoperability 
between IGMP version 2 and version 1, see sections 4 and 5 of 
Internet Group Management Protocol (RFC 2236).

Call Schedule 
(PPPoE and PPTP 
encapsulation) 

Apply call schedule sets for this remote node. Use the 

Call 

Schedule

 screens to configure call schedule sets (see 

Chapter 21, 

“Call scheduling screens,” on page 385

).

Windows 
Networking 
(NetBIOS over 
TCP/IP):

Windows Networking (NetBIOS over TCP/IP): NetBIOS (Network 
Basic Input/Output System) are TCP or UDP packets that enable a 
computer to connect to and communicate with a LAN. For some 
dial-up services, such as PPPoE or PPTP, NetBIOS packets cause 
unwanted calls.

Table 22   

WAN: IP

Label

Description

Summary of Contents for BSR222




































































































































































































































































































































































































































































Reviews:

No comments