manualshive.com logo in svg

Nortel 8300 Series, Reference Manual, Page: 81 / 220

Share
Download
Nortel 8300 Series Reference Manual Download Page 81

Chapter 4 SMP log error messages

81

System Messaging Platform Reference Guide

 

F Messages

Message

fail config STG for mgmt VLAN

Severity

ERROR

Description

This message is generated when an attempt to create an STG for the specified 
VLAN fails.

Synopsis

Cannot create STG.

Action

Contact customer support for further troubleshooting.

Message

failed deleting a route in rcIpRouteTblSet()

Severity

ERROR

Description

This message is generated when the deletion of a route fails.

Synopsis

Cannot delete the route.

Action

Contact customer support for further troubleshooting.

Message

Failed to assign IP address to mgmt VLAN

Severity

ERROR

Description

This message is generated when assigning an IP address to the management 
VLAN fails during the system initialization pre-configuration process.

Synopsis

Cannot assign IP address.

Action

Contact Customer Support for further troubleshooting.

Message

Failed to connect TCP socket to server xyz port xyz, errno xyz

Severity

ERROR

Description

Failed to set socket connect operation to specific server

Synopsis

Check server configuration

Action

N/A

Message

Failed to create IMC VLAN

Severity

ERROR

Description

This message is generated when creating an IMC VLAN fails during the system 
initialization pre-configuration process. 

Synopsis

Cannot create VLAN.

Action

Contact customer support for further troubleshooting.

Summary of Contents for 8300 Series





























































































































































































































Reviews:

No comments