manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 53 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 53

Chapter 1 About Ethernet Switches 325 and 425

53

System Configuration Guide

 

VLAN Configuration Control is only applied to ports with the tagging modes of 
Untag All and Tag PVID Only. Ports with the tagging modes of Tag All and 
Untag PVID Only are not governed by VLAN Configuration Control. Ports with 
the tagging modes of Tag All and Untag PVID Only can belong to multiple 
VLANs regardless of VLAN Configuration Control settings and must have their 
PVID manually changed.

For more information, refer to 

Configuring VLANs, Spanning Tree, and 

MultiLink Trunking for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320986-A).

Port mirroring configuration rules

Additional port mirroring configuration rules are available in 

System Monitoring 

Guide for Nortel Ethernet Switches 325 and 425, Software 
Release 3.6

(320989-A).

Other features

SFP GBIC Support on the Ethernet Switch 425

Small Form Factor Pluggable transceivers (SFPs) are hot-swappable input/output 
enhancement components designed for use with Nortel products to allow Gigabit 
Ethernet ports to link with other Gigabit Ethernet ports over various media types. 

The Ethernet Switch 425 supports the following SFPs:

•

1000Base-SX SFP GBIC (mini-GBIC, connector type: LC)

•

1000Base-SX SFP GBIC (mini-GBIC, connector type: MT-RJ)

•

1000Base-LX SFP GBIC (mini-GBIC, connector type: LC)

•

CWDM SFPs

For more information about the SFP GBICs see 

Appendix A, “Installing an SFP 

Transceiver,” on page 409

.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments