manualshive.com logo in svg

Nortel 425-24T, Configuration Manual, Page: 315 / 488

Share
Download
Nortel 425-24T Configuration Manual Download Page 315

Chapter 7 System configuration using the CLI

315

System Configuration Guide

 

default ui-button command

The 

default

 

ui-button

 command restores UI button to its default 

configuration. The syntax for the 

default

 

ui-button

 command is:

default ui-button

The 

default

 

ui-button

 command is in the config command mode.

The 

default

 

ui-button

 command has no parameters or values.

no ui-button command

The 

no

 

ui-button

 command disables the UI button. 

The syntax for the 

no

 

ui-button

 command is:

no ui-button

The 

no ui-button

 command is in the config command mode.

The 

no ui-button

 command has no parameters or values.

Upgrading software

You can download the Ethernet Switches 325 and 425 software image that is 
located in non-volatile flash memory. To download the Ethernet Switches 325 and 
425 software image, a properly configured Trivial File Transfer Protocol (TFTP) 
server must be present in your network, and the policy switch must have an IP 
address. To learn how to configure the switch or stack IP address, refer to 

“Assigning and clearing IP addresses” on page 252

.

This section covers:

Caution: 

Do not interrupt power to the device during the software 

download process. A power interruption can corrupt the firmware image.

Summary of Contents for 425-24T









































































































































































































































































































































































































































































































Reviews:

No comments